1600
ANTI CORROSIVE COATING
Formerly 141
One coat. Quick drying.
Reliable corrosion protection coating of steel reinforcement.
- 1hr quick-drying: for fast construction progress.
- Simple one coat application.
- Protective coating for reinforcement against corrosion. For repairing reinforced concrete.
- Strong protection against the penetration of water and chlorides.
- With corrosion inhibitors: Treated reinforcement can remain exposed for up to 4 weeks for subsequent mortar application.
- Cement based: With excellent adhesion to steel and concrete.
- One-component: only add water.
Area of application
- Outdoor: floor + wall + ceiling
- Indoor: floor + wall + ceiling
Processing method
- For hand processing
- For corrosion protection of all metal parts in the sanitation of ferro-concrete structures. Protection of reinforcement in case of insufficient coverage.
- For secondary protection of metal reinforcement in concrete structures.
Processing details
Learn more about technical details for processing this product.
Substrate requirement
The substrate (steel) must comply with the applicable standards, must be solid, free of loose particles, free of dust. It must be sufficiently dry. The surface shall not be frozen.
In case of major degradation of the substrate, we recommend a consultation with a structural engineer.
Substrate preparation
On all corroded steel, remove loose parts and corrosion layers. Clean the steel to a silvery shine (Sa 2). Pay particular attention to the back of the exposed reinforcement. High pressure cleaning or sanding is recommended. If this is not possible for technical reasons, the reinforcement must be carefully cleaned mechanically (e.g. with a steel brush). In areas where corrosion due to chloride has occurred, rinse the steel with pressure water immediately after cleaning to remove any residual corrosive substances.
Preparation of the mixture
Směs připravíte tak, že nejprve smícháte 2/3 suché směsi s plným objemem vody. Míchejte ji 2 min. a poté za stálého míchání přidejte zbývající suchou směs a míchejte 3 min. do požadované konzistence. Smíchejte do homogenní směsi bez hrudek. Směs nechte odpočinout. Poté znovu krátce promíchejte. K míchání použijte pomaloběžný pádlový mixér s maximální rychlostí 800 otáček za minutu. K míchání směsi použijte pitnou vodu nebo vodu odpovídající normě EN 1008.
Water demand
| Quantity | Liters (Min) | Liters (Max) |
|---|---|---|
| 1 kg | 0.252 L | 0.264 L |
| 5 kg | 1.26 L | 1.32 L |
Mixing
Processing instructions
Apply the paint to the cleaned reinforcement with a medium-hard brush. Water must not stand on the reinforcement. Apply the coating as soon as possible after completion of the preparation work. Coat the surface of the reinforcement with one full and complete coat of approx. 0.5 mm thick. Take great care on the back of the exposed reinforcement.
There is no harm in painting the adjacent concrete, but the paint must always be spread in a thin layer to ensure high adhesion of the remedial mortar.
The painted reinforcement may be left exposed to the weather for up to 4 weeks before applying the sanitation mortar. Check the continuity of the coating before covering.
Sanitation mortar or concrete may be applied first after 1 hour when the coating has dried and there is no risk of coating failure.
Application thickness
| Minimum layer thickness | 0.5 mm |
|---|---|
| Recommended layer thickness | 0.75 mm |
| Maximum layer thickness | 1 mm |
Consumption
Yield
| Material consumption | Yield |
|---|---|
| 5 kg | 6.666 m² |
Working time (potlife)
40 min
Treatment after application
After application, the direct negative effects of sun, heat, humidity and draughts should be avoided. Protect from frost and rain. Direct heating of the surface is prohibited.
Tool and cleaning instructions
Wash off tools with water immediately after finishing work. Clean dried residues mechanically.
Technical parameters
| Main binder | Grey cement |
| Made of material | Mineral filler, corrosion inhibitors, other additives improving processing and utility properties of the product. |
| Flammability class | A1 |
| Wet density in Kg/m³ from | 1500 |
Download
Contact: Can we help you?
Ask us your question. Write to us whenever you want. We will reply within 48 working hours.
Telephone 800 022 848
Contact us on the toll-free Customer hotline
- Opening hours: weekdays 7:30 a.m.–3:00 p.m.
- Email: info@cemix.cz